Body Builder Connectors and Lighting Interface

Quick Reference Guide for Body Builder Connectors, Pinouts, Mating Connector Housing Assembly and Terminal Part Numbers. Also end of frame Lighting Connector information provided.

Download as PDF

Body Builder Harness

Body Builder Harness with Auxiliary Switch Overlay (Dash), VN

body harness

W3035627

  1. Dual power take off (PTO), Switch
  2. Body Builder Module (BBM) Electronic Control Unit (ECU)
  3. Splice Pack (5K141B)
  4. Main Cab (OPT5)
  5. Main Cab (OPT1587)
  6. Main Cab (MCBB)
  7. Body Builder Connector # 4 (203D.A)
  8. Body Builder Connector # 3 (203C.A)
  9. Body Builder Connector # 3 (203C)
  10. Body Builder Connector # 4 (203D)
  11. Terminating Resistor (R08A)
  12. Overlay Options (OPT3)

Body Builder Harness with Auxiliary Switch Overlay (Dash), VHD

switch overlay

W3118564

  1. Wiring Harness
  2. BB Module
  3. Datalink Option Connector
  4. Datalink Connection
  5. Body Builder Module Connection
  6. Body Builder Module Connection
  7. Auxiliary Switch Connectors
  8. To 141A Splice

Body Builder Connections End of Frame

Body Builder connections end of frame provides access to the electrical lighting connections. The circuits provide for separate STOP and TURN signals.

Notes:

  • Mating connectors are located in the cab when the truck is delivered.
  • If a combined Stop/Turn is required, use the in-line connection point in the rear lighting in-line connector.

inline connection point

W3118341

Fig. 1 Connectors located at the end of frame

The connections are grouped into three connectors:

3-Way Metri-Pack 480 Series Connector
Cavity Assignment Wire Color Description
1 Black Trailer Marker/Clearance lamps
2 Brown Trailer Tail lamps
3 Red Stop Lights

480 series connector

W3118342

3-Way Metri-Pack 630 Series Connector
Cavity Assignment Wire Color Description
A Yellow LH Turn Signal Light
B Green RH Turn Signal Light
C Blue Auxiliary (12V ignition power)

630 series connector

W3118343

1-Way Maxi Connector
Cavity Assignment Wire Color Description
A White Ground

maxi connector

W3118344

Body Builder Pass Through Connectors (VHD)

Three body builder option connectors are in the cab and engine harnesses. These wires provide a pass-through for add-on wiring from the engine compartment to inside the cab.

They are single wires, with plugged connectors, circuit numbers 999A, 999B, and 999C. They are located near the engine pass-through on the engine side, and inside the dash, behind the instrument cluster, on the cab side.

Note: A body builder connector is installed with 14 wires for passing circuits through the cab floor.

vhd

W8003318

Option Connectors, Driver Side Engine Compartment

option connectors

W3118565

Body Builder Connector

VHD Body Builder Connectors

Connector Usage/Gender Information

Connector/Item Connector Series Gender On-Vehicle
BB Connector #1 (ELCE-PK) 280-GT, Unsealed 16-way Female Housing/Female Terminals
BB Connector #2 (ELCE-PK) 280-GT, Unsealed 16-way Male Housing/Male Terminals
BB Connector #3 (ELCE-CK) 150-GT, Unsealed 16-way Female Housing/Female Terminals
BB Connector #4 (ELCE-CK) 150-GT, Unsealed 16-way Male Housing/Male Terminals
Snow Plow Prep. 280-GT, Sealed 10-way Male Housing/Male Terminals
Cable kit 85148537 is for connectors 1 and 2.
Cable kit 85146080 is for connectors 3 and 4.

Delphi/Packard 150-GT, Unsealed 16-way

Female Housing/Female Terminals

female terminals

W9000766

Item Supplier P/N VOLVO P/N
Housing 15332177 20481359
Terminals-choose by conductor size:
0.35–0.50 mm² (0.013-0.019 in²)
0.75–1.00 mm² (0.029-0.039 in²)
12191811
12191812
N/A
N/A
Cable Seals-Not Required
Cavity Plugs-Not Required

Male Housing/Male Terminals

male terminals

W9000767

Item Supplier P/N VOLVO P/N
Housing 15332182 20481361
Terminals-choose by conductor size:
0.35–0.50 mm² (0.013-0.019 in²)
0.75–1.00 mm² (0.029-0.039 in²)
15304701
15304702
N/A
N/A
Cable Seals-Not Required
Cavity Plugs-Not Required

Delphi/Packard 280-GT, Sealed 10-way

Female Housing/Female Terminals

280 female terminals

W9000768

Item Supplier P/N VOLVO P/N
Housing 5326660 20478205
Terminals-choose by conductor size:
0.35–0.50 mm² (0.013-0.019 in²)
0.75–1.00 mm² (0.029-0.039 in²)
1.50-3.00 mm² (0.059-0.118 in²)
 15304718
15304719
15304720
N/A
N/A
N/A
Cable Seals-choose by insulation O.D.
1.85-2.25 mm² (0.072-0.088 in²)
2.50-3.20 mm² (0.098-0.125 in²)
3.40-3.90 mm² (0.133-0.153 in²)
15366066
15366067
12191235
N/A
N/A
N/A
Cavity Plugs 15305170 N/A

Male Housing/Male Terminals

male terminals 769

W9000769

Item Supplier P/N VOLVO P/N
Housing 15326661 20478204
Terminals-choose by conductor size:
0.35–0.50 mm² (0.013-0.019 in²)
0.75–1.00 mm² (0.029-0.039 in²)
1.50-3.00 mm² (0.059-0.118 in²)
15304730
15304731
15304732
N/A
N/A
N/A
Cable Seals-choose by insulation O.D.
1.85-2.25 mm² (0.072-0.088 in²)
2.50-3.20 mm² (0.098-0.125 in²)
3.40-3.90 mm² (0.133-0.153 in²)
15366066
15366067
12191235
N/A
N/A
N/A
Cavity Plugs 15305170 N/A

Delphi/Packard 280-GT, Unsealed 16-way

Female Housing/Female Terminals

unsealed 16 way

W9000770

Item Supplier P/N VOLVO P/N
Housing 15326952 20378995
Terminals-choose by conductor size:
0.35–0.50 mm² (0.013-0.019 in²)
0.75–1.00 mm² (0.029-0.039 in²)
4.00-5.00 mm² (0.157-0.196 in²)
15304711
15304712
15304713
N/A
N/A
N/A
Cable Seals-Not Required
Cavity Plugs-Not Required

Male Housing/Male Terminals

male terminals 771

W9000771

Item Supplier P/N VOLVO P/N
Housing 15326956 3186494
Terminals-choose by conductor size:
0.35–0.50 mm² (0.013-0.019 in²)
0.75–1.00 mm² (0.029-0.039 in²)
4.00-5.00 mm² (0.157-0.196 in²) 
15304723
15304724
15304725
N/A
N/A
N/A
Cable Seals-Not Required
Cavity Plugs-Not Required

Basic Prep Kit

“Basic” Prep Kit - ELCE-PK (Sales Code: L3–A1)

The basic prep package installed in all VHDs prewires for the most commonly used body builder circuits. It includes fused battery power circuits (both switched and unswitched), ground, Reverse power, and access to the 'stalk' PTO engine speed adjustment circuits.

A 31-way pass through connector in the cab floor is included for passing circuits from inside to outside the cab in a safe, weather-proof manner. In addition, there are two unassigned circuits (MAAA1 and MAAB1) installed in the 102-way pass through from the cab to the engine compartment for body builder use.

If the vehicle is equipped with an Allison Transmission, additional Allison-specific circuits are pre-wired to the body builder connector, as well.

The following tables list the pinout and mating connector information for the 16-way body builder connectors which are part of the ELCE-PK package, located on the cab floor between the seats.

Description of Circuits included in ELCE-PK (Basic Prep Kit)

This is the 'basic' prep kit; Available with all engines. Content is the same for all engines, but differs depending on transmission.

Note: Verify fuse numbers and values with the fuse legend decal installed in your particular vehicle.

Connector #1

Type: 16-way, unsealed Packard GT 280-series (female housing w/ female terminals)

Location: Between driver and passenger seat

Present: Always present with ELCE-PK option (sales code L3-A1)

Pin Circuit
Gen 2
2018
Circuit
Gen 1
Pre 2018
Description Notes
A X03DH3 X03EA2 Body Builder Ground Return 30A Max.
B HA10AB MABA1 Alternator “R” Terminal N/A
C F19A1 F43A2 Fused, Unswitched Battery Power 30A “Body Builder” Maxi Fuse; 25A Max.
D F35A1 F65A1 Fused, Ignition Switched Power 15A “IGN-X” fuse; draw 12A Max.
E N122A1 N122A1 Allison Defined N/A
F N123A1 N123A1 Varies; typically Reduced Eng Load at
Stop Input
Typ. Reduced Engine Load at Stop Input
G F49A4 F62F2 +12V when transmission in REVERSE Fed via “Body Builder Reverse” fuse; 5A
Max.
H F47A1 F64A1 Fused, Ignition-Switched Power 15A “IGN-Y” fuse; draw 12A Max.
J F46A1 F29A1 Fused, Ignition-Switched Power 15A “IGN-Z” fuse; draw 12A Max.
K CAKJ5C5 MAKA1 Stalk PTO engine speed increase Active High Input
L CALJ5F5 MALA1 Stalk PTO engine speed decrease Active High Input
M F65A3 F34C3 Remote PTO1 Output Active High Output; 4A Max.
N CA1AN F34E3 Remote PTO1 Input/Activation Active High Input
P N/A N/A Empty  
R N/A N/A Empty  
S N/A N/A Empty  

Connector #2

Type: 16-way, unsealed Packard GT 280-series (male housing w/ male terminals)

Location: Between driver and passenger seat

Present: Present with ELCE-PK option (only when Allison transmission installed)

Pin Circuit
Gen 2
2018
Circuit
Gen 1
Pre 2018
Description Notes
A N/A N/A Empty  
B FR15A87A NABA1 N.C. contact of relay controlled by A112 Typical PTO Enable Output
C FR15A87 NACA1 N.C. contact of relay controlled by A112
D FR15A30 NADA1 COM contact of relay controlled by A112
E FR16A87 NAEA1 N.O. contact of relay controlled by A114 Typical Neutral Indicator for PTO
F FR16A87A NAFA1 N.C. contact of relay controlled by A114
G FR16A30 NAGA1 COM contact of relay controlled by A114
H N103A2 N103A2 Switch Return (Ground) Use for all Allison-connected active low
inputs
J N117A2 N117A2 Allison defined Typically AutoNeutral Input
K N143A1 N143A1 Allison defined Typically PTO Enable Input
L XO3BA XO3BA  Allison ECU Power Ground Use for ground-connected Allison Outputs
M N142A1 N142A1 Allison defined Typically Range Hold Input
N N101A1 N101A1 Allison defined Typically Range Inhibit Input
P N125A1 N125A1 Allison defined Typically Speedometer Output
R N113A1 N113A1 Allison defined Output; varies by application
S N105A1 N105A1 Allison defined Typically 'Speed Indicator A' Output
1 The function of all Allison-defined circuits (Axxx) will depend on the chosen Vocational Package. Always refer to Allison Documentation for details. 

Note: Allison-Only Circuits numbered "Axxx": Refer to Allison Transmission documentation or Body Builder Transmission service bulletins (using the "Axxx" circuit references) to determine the exact function of each Allison circuit, as they can vary depending upon the vocational package chosen.

Connector/Mating Part Information

Note: Unless otherwise indicated, all part numbers are Delphi / Packard:

Connector/Item Supplied on vehicle Mate required to plug into vehicle
Connector #1 Packard 280-GT series (unsealed), 16-
way; Female housing & Terminals
Packard 280-GT series (unsealed), 16-
way; Male housing & Terminals
Housing Assy: Packard PN 15326952 VOLVO PN
20378995
Packard PN 15326956
VOLVO PN 3186494
Terminals Female Terminals, size as required Male Terminals: Packard 15304723 (0.75
~ 1.00mm²)
Packard 15304724 (1.50 ~ 3.00 mm²)
Packard 15304725 (4.00 ~ 5.00 mm²)
Connector #2 Packard 280-GT series (unsealed), 16-
way; Male housing & Terminals
Packard 280-GT series (unsealed), 16-
way; Female housing & Terminals
Housing Assy: Packard PN 15326956 VOLVO PN
3186494
Packard PN 15326952
VOLVO PN 20378995
Terminals: Male Terminals, size as required Female Terminals: Packard 15304711
(0.75 ~ 1.00 mm²)
Packard 15304712 (1.50 ~ 3.00 mm²)
Packard 15304713 (4.00 ~ 5.00 mm²)

Battery and Ignition Feed circuits (F43A1, F65A1, F64A1, and F29A1)

These unswitched and ignition-switched power feeds are provided for body builder's use. Note that each circuit is fused by either a Maxifuse in the Power Module, and/or a minifuse in the standard Fuse and Relay Center. Observe the maximum current capabilities of each circuit.

Note: Verify fuse numbers and values with the fuse legend decal installed in your particular vehicle.

Circuit Fuse/Fuse Size Maximum Usable Current
F43A1 F43/10A/30A 25 A (80% of fuse rating)
F65A1 F65/15A 12A
F64A1 F64/15A 12A
F29A1 F29/15A 12A

Note: NEVER increase the size of the fuse beyond what is listed above (or on the Fuse and Relay Center decal). If needed for the application, though, the fuse size may be reduced as dictated by load of the attached equipment.

Special NOTE for the F65A1 circuit (Fuse F65) and F64A1 circuit (Fuse F64)
These circuits are in the electrical 'path' of the PLC4TRUCK signal as it makes its way from the trailer (AUX circuit) to the tractor ABS ECU. Do not use the F65A1 or F64A1 circuits for powering items such as:
• large inductive or capacitive loads such as electric motors or continuously-activated solenoids
• add-on equipment which uses a type of Power Line Carrier (PLC) communication which is not compatible with the PLC4TRUCK signal 
Doing so may affect the PLC4TRUCK signal, resulting in a loss of trailer ABS malfunction indication. 
Likewise, do not use the F65A1 or F54A1 circuits for powering sensitive communication
If you will be connecting to a trailer equipped with the PLC4TRUCK system (basically, any air-braked trailer manufactured after March, 2001), it will be the user's responsibility to ensure that any add-on electrical equipment does not interfere with the trailer ABS malfunction circuit function.

Ground Circuit (X03EA2)

This ground circuit should be used as much as possible for all body builder ground needs. It connects to a ground stud on the vehicle firewall which is a central ground point for all vehicle electrical loads. Note the maximum current capacity of the circuit (dictated by the 6.0mm2 conductor size) of 30A.

Reverse Circuit (F63H2)

This is a 10A (max) circuit, live when the transmission is placed into REVERSE gear. It shares a relay (RLY14) and fusing (F63) with the lift-axle logic: when the transmission is not in reverse, the lift axles are allowed to operate; when the transmission is in reverse, circuit F63H2 receives power.

Note: OVERLOADING CIRCUIT F63H2 (and causing F63 to blow) WILL PREVENT PROPER OPERATION OF THE LIFTAXLES

Allison Controlled Relays

(NADA1/NACA1/NABA1 and NAEA1/NAFA1/NAGA1) - Allison Transmission Only

Two relays are provided which are controlled by the Allison Transmission circuits N145A1 and N130A1. See the diagram below.

allison controlled relays

W3127852

Refer to either Allison Transmission documentation, or the Body Builder Transmission service bulletins, for details on the exact functions of these circuits, as they differ depending upon which vocational package was chosen.

Stalk PTO Engine Speed INC/DEC (MAKA1, MALA1)

These circuits are provided for "remote" adjustment of the engine speed while operating in "stalk PTO" mode. They are connected to relays which operate in parallel with the "SET+" and “SET-" stalk switches, and will allow trimming of the PTO engine speed just as if the in-cab controls were used, except for the added requirement that the vehicle's park brake must be set in order to use these "remote" control circuits.

As with the in-cab stalk PTO mode of operation, the Cruise Control On/Off switch must remain "on". The 'base' PTO set speed should be selected before exiting the cab.

These circuits are usable on both VOLVO and Cummins engines (VNL only), with the same mode of operation that each engine has concerning the in-cab "stalk PTO" operation. Refer to the "Stalk PTO" topic in the "PTO Functions" section of this document.

PTO1 Input/Enable and Output

(F34E3, F34C3) - VOLVO Engine Only

These circuits provide access to the single PTO function of the VECU, and are usable with the VOLVO engine only. If more than one PTO function is required for your application with the VOLVO engine, a body builder module (BBM) ECU will be required - refer to the section on the ELCE-CK prep package.

For a complete description of the PTO1 Input/Enable and Output functions of the VECU, please refer to the "VECU Functions" section of this document.

For all wired-PTO functions with the Cummins engines, it will be necessary to wire directly to the Engine ECU. Refer to the section on the ELCE-EK prep package for available pre-wired circuits, and also to Cummins Engine Company documentation for PTO operation with these engines.

Notes:

  1. ELCE-PK is standard equipment on all VHDs (truck and tractor), unless specified otherwise.
  2. ELCE-PK is available with all engines.
  3. ELCE-PK is available with all transmissions; additional content is included when Allison transmission is specified.
  4. The wiring for the PTO Relay (RLY07), PTO DASH SWITCH, and "PTO" fusing are present in every VHD; the components themselves are only installed when one of the available PTO-prep options are ordered.
  5. The function of all Allison Transmission circuits (Axxx) will depend on the chosen Vocational Package; REFER TO ALLISON DOCUMENTATION FOR DETAILS.

VHD Body Builder Wiring

vhd body builder wiring

W3119185

“Complete” Prep Kit; Including BBM ECU; ELCE-CK (Sales Code: L3-C1)

The "complete" prep kit adds a body builder module (BBM) electronic control unit (ECU) and associated wiring to the standard "basic" prep kit. The ELCE-CK kit is only available with a VOLVO engine.

The following tables list the pinout and mating connector information for the 16-way body builder connectors which are part of the ELCE-CK package, located on the cab floor between the seats.

Description of Circuits Included in ELCE-CK ("Complete" Prep Kit)

In addition to all the circuits listed above in the ELCE-PK package, the ELCE-CK package adds the body builder module (BBM) electronic control unit (ECU), together with the following circuits brought out to two additional connectors located between the seats (same location as -PK package).

Connector #3

Connector # BB-EK

Type: 16-way, unsealed Packard GT 150-series (female housing w/ female terminals)

Location: Between driver and passenger seat

Present: Always present with ELCE-CK option (sales code L3-C1)

Pin Circuit
Gen 2
2018
Circuit
Gen 1
Pre 2018
Description Notes
A X03DB16 X03EA21 Ground return for all BBM-connected Inputs  
B MB5A3 MB5A3 +V Power for BBM-connected Switches Limit to -10 switches per +V output
C MB19A1 MB19A1 +V Power for BBM-connected Switches Limit to -10 switches per +V output
D MA18A2 MA18A2 PTO2 Input/Enable All PTO inputs are Active High; See VECU (ELCE-PK) for PTO1 Input/Enable
E MA19A1 MA19A1 PTO3 Input/Enable
F MA20A1 MA20A1 PTO4 Input/Enable
G MA4A1 MA4A1 PTO1 Engine Speed Control Input Active High Inputs
H MB21A1 MB21A1 PTO2 Engine Speed Control Input
J MA3A1 MA3A1 PTO3 Engine Speed Control Input
K MA5A1 MA5A1 PTO4 Engine Speed Control Input
L MB2A1 MB2A1 PTO2 Output Active Low Outputs; limit to 1 Amp per output. See VECU (ELCE-PK) for PTO1 Input/Enable
M MB3A1 MB3A1 PTO3 Output
N MB4A1 MB4A1 PTO4 Output
P MA1A1 MA1A1 Remote PTO Engine Speed DECrement Active High Inputs; act on PTO2-4 only
R MA2A1 MA2A1 Remote PTO Engine Speed INCrement
S F44BS N/A Hood Position Switch Optional

Connector #4

Connector # BB-EK

Type: 16-way, unsealed Packard GT 150-series (male housing w/ male terminals)

Location: Between driver and passenger seat

Present: Always present with ELCE-CK option (sales code L3-C1)

Pin Circuit
Gen 2
2018
Circuit
Gen 1
Pre 2018
Description Notes
A MA6A1 MA6A1 Engine Shutdown #1 Input (See Note 1) Normally Open (N.O.) Switch to +V
B MA27A1 MA27A1 Engine Shutdown #2 Input (See Note 1) Normally Closed (N.C.) Switch to Ground
C MA7A1 MA7A1 Forced Idle/Throttle Interlock Input Active High Input
D MA17A1 MA17A1 Engine Speed Limit Input Active High Input
E MA25A1 MA25A1 Engine Torque Limit Input Active Low Input
F MA26A1 MA26A1 Road Speed Limit Input Active Low Input
G MA24A1 MA24A1 PTO Neutral Interlock Input Active Low Input
H MA28A1 MA28A1 PTO Low Split Gear Interlock Input Active Low Input
J MA29A1 MA29A1 Split Shaft PTO Input Active High Input
K MB12A1 MB12A1 Remote Throttle Enable Input Active Low Input; See Note 2 and 3
L MB10A1 MB10A1 Remote Throttle V-Ref (5V) Output See Note 2 and Note 3.
Use twisted-trio wiring for these three circuits
M MB9A1 MB9A1 Remote Throttle Sensor/Signal Input
N MB22A1 MB22A1 Remote Throttle Ground Reference
P MB28A1 MB28A1 Road Speed Output ("C3" Output) Active High Output
R MB16A1 MB16A1 System Warning Output Active Low Output
S MB18A1 MB18A1 Databus Triggered Output Active Low Output

Notes:

  1. Engine Shutdown Input #1 is always enabled. Do not install a switch at that position if function is not required. Engine Shutdown Input #2 must be enabled in software, and once enabled will shutdown the engine unless ground is present at that input.
  2. For stationary 2nd Throttle use, it is recommended to add a redundant Park Brake pressure switch in series with the Remote Throttle Enable Input (see schematic). This will allow remote throttle only while the park brake is set. DO NOT tie into the factory-installed Park Brake pressure switch for this purpose.
  3. For non-stationary 2nd Throttle use, an Accelerator Pedal with Idle Validation Switch (IVS) is required. Circuits for the IVS are not brought out to Body Builder Connector #4. Refer to the BBM ECU section of this document for details on the circuitry needed for a 2nd driving position.

Connector/Mating Part Information

All part numbers shown are Delphi / Packard, unless otherwise noted.

Connector/Item Supplied on vehicle Mate required to plug in to Vehicle
Connector #3 Connector #3 Packard 150-GTseries (unsealed), 16-way; Female housing & Terminals Packard 150-GT series (unsealed), 16-way; Male housing & Terminals Packard 150-GT series (unsealed), 16-way; Male housing & Terminals
Housing Assembly Packard PN 15332177
VOLVO PN 20481359
Packard PN 15332182
VOLVO PN 20481361
Terminals Packard 12191812 (0.75 ~ 1.00 mm²) Packard 15304702 (0.75 ~ 1.00 mm²)
Packard 15304701 (0.35 ~ 0.50 mm²)
Connector #4 Packard 150-GT series (unsealed), 16-way;
Male housing & Terminals
Packard 150-GT series (unsealed), 16-way;
Female housing & Terminals
Housing Assembly Packard PN 15332182
VOLVO PN 20481361
Packard PN 15332177
VOLVO PN 20481359
Terminals Packard 15304702 (0.75 ~ 1.00 mm²) Packard 12191812 (0.75 ~ 1.00 mm²)
Packard 12191811 (0.35 ~ 0.50 mm²)

Notes:

  1. ELCE-CK is standard equipment on VHD trucks; optional on VHD tractors.
  2. ELCE-CK includes all contents of the 'basic' prep (ELCE-PK).
  3. ELCE-CK is only available with VOLVO engines.
  4. ELCE-CK is available with all transmissions.